Two years ago I rejected a 240-page client deliverable because of thin black lines running down every page. The admin before me would've rerun the job and called it a day. I spent 18 of the next 20 minutes on diagnosis and two on the actual fix.
That's the deal with "my Brother printer has lines when printing." It's not one problem. It's at least four, and the fix for one tends to make the others worse. So before you start pulling cartridges or calling the service line, figure out which situation you're in. That's the whole article—a decision tree, not a single answer.
Quick context on me: I manage print quality and brand review for a professional services firm. Between client deliverables and vendor sign-offs, I see roughly 300 to 400 printed documents a month. In 2023, we had to reprint and redeliver 14 signed contracts because of defects that made it past first-round QC—about $9,000 in paper, courier, and duplicate processing. That's the number that shaped how I look at a printer problem now. Diagnosis first. Always.
The type of line is the diagnosis
Grab a printed page—not the top sheet from the tray, but one from mid-stack so heat and curl don't skew what you're seeing. Hold it up to a lamp, and look for one of four patterns:
- Vertical lines (top to bottom)
- Horizontal bands (side to side)
- Repeating marks at regular vertical intervals
- White gaps where print should be
In our QC log, vertical lines and horizontal bands have almost no diagnostic overlap. Treating them as the same problem is why people replace good parts. Each pattern points to a specific component.
Scenario A: Vertical lines
Most likely cause: the drum unit or a dirty corona wire.
From the outside, vertical lines on a laser printer look like the printhead—or sometimes the fuser—is failing. The reality is that on most Brother laser models, the drum is a separate wear item, and a single scratch or a smudged corona wire produces exactly this pattern. On current HL and MFC laser models, check whether your drum is a separate part (the DR-series) or combined with the toner; if it's separate, the drum is the first thing to look at, not the printhead.
Two checks before you order anything:
- Corona wire cleaning. Many Brother laser models have a small cleaning slider by the drum access. Slide it across a few times. If the lines soften, you've found your cause. This is a two-minute fix and doesn't cost anything.
- Visible drum damage. Pull the drum (or drum-toner unit)—carefully, in dim light, avoiding fingerprints on the green drum surface—and look for a scratch or a line of debris on the drum itself. If you see it, replace the drum. This is a parts-replacement fix, not a "clean it with alcohol" fix.
Scenario B: Horizontal bands
Most likely cause: the fuser or the transfer roller.
This is where most DIY attempts go wrong, and it's where I burned $340 on a drum unit I didn't need. Horizontal bands—whether they're dark streaks or faded zones running side to side—usually indicate heat-related problems with the fuser, or contamination on the transfer roller. Neither is a drum problem, but both look like one if you're going by "the print is bad."
Quick test: run a self-test page (from the control panel menu—Brother models usually have a print-quality or self-test option) and compare the spacing of the bands. If the bands repeat down the page, it's a rotating component (see Scenario C). If they don't repeat, they're stationary—usually the fuser.
If it's the fuser, stop. Fuser replacement involves disassembling the printer in a hot-component area and usually voids your remaining service coverage if you do it yourself. In my experience, this is where the DIY boundary should end.
Scenario C: Repeating marks at regular intervals
This one gives you a real diagnostic shortcut, so use it before ordering anything.
Repeating defects at regular intervals—whether they're dark marks, light marks, or bands—are the fingerprint of a specific rotating component. The spacing between marks corresponds to the circumference of whichever roller is causing the issue: the drum, transfer roller, or fuser. Your service manual lists the circumference for each, and comparing the spacing you measure to those numbers tells you which part to look at first.
I'm not exaggerating when I say this single measurement has saved me thousands. On one job, we were about to replace a drum (roughly $120 in parts and labor) when the spacing said "fuser." That became a warranty call to Brother, and it cost us nothing.
A note on the measurement: use a ruler, mark the start of two identical marks, and count in millimeters. Don't eyeball it. The whole value of the shortcut collapses if the input is sloppy.
Scenario D: White gaps or missing print
Two causes worth knowing, one worth doing yourself.
If the "lines" are actually white—places where ink should have printed but didn't—you're almost always in one of two situations. On a laser, it's low toner (needs a cartridge) or a drum that's reached end-of-life. On an inkjet, it's a clogged printhead nozzle, and Brother's built-in nozzle check and cleaning routine handles most of those.
From the outside, this looks like the same problem as vertical lines. It isn't. On an inkjet, the fix is a nozzle check and a cleaning cycle—about 90% of the time, one cycle clears it. On a laser, it's a cartridge-level diagnosis. Trying drum replacement on an inkjet, or a nozzle cleaning on a laser, wastes time and occasionally makes things worse.
DIY or service call: the boundary I've learned to respect
There's a version of this article that tells you to look up your model's service manual and become a printer repair tech. That's not the article I'm writing. I tried to be that person for the first four years of managing print output, and it cost more money than it saved.
The line I've drawn is this:
- Do it yourself: corona wire cleaning, nozzle check and cleaning, self-test pages, drum replacement on models where it's an external swap.
- Call service (or warranty): fuser replacement, gear-drive components, anything that requires disassembly near the heat assembly or sits beneath the paper path.
- Third-party toner: a judgment call, not a warranty question. Under the FTC's Magnuson-Moss Warranty Act (the FTC's warranty guidance is at ftc.gov), using a third-party cartridge doesn't automatically void your printer warranty—the manufacturer would have to prove the third-party part caused the damage. That said, quality varies dramatically across suppliers. In 2022 we saved $40 per cartridge by switching suppliers; six months later two drum units were failing early. The drum replacement cost $280, which ate the annual savings on our most-used printer. Not a warranty issue—just a bad business decision I won't repeat on client-facing output.
"I'm not the repair tech" is a fact about my role, not a limit on my understanding of the printer. Knowing the boundary is what keeps reprint costs down. Chasing every fix myself never did.
So which scenario are you in?
One page, one lamp, one minute:
- Vertical lines → Scenario A. Clean the corona wire first. If that doesn't fix it, check the drum.
- Horizontal bands → Scenario B. Run a self-test, check whether the bands repeat. If they don't, it's the fuser—call service.
- Repeating marks at regular intervals → Scenario C. Measure the spacing. Compare to the drum, transfer, and fuser circumferences in your service manual. Order the part that matches.
- White gaps → Scenario D. On an inkjet, run a nozzle check. On a laser, check toner level, then drum.
If two patterns show up on the same page—say, vertical lines plus a repeating mark—the repeating defect is almost certainly the more specific signal, and I'd start there. Diagnose the repeating issue first, then re-evaluate whether the vertical lines are still there. They often aren't.
The final thing I'll say: if you get to the point where you've replaced two parts and the problem persists, stop. At that point the diagnosis is wrong, and a service call is cheaper than a third part. I say this from the position of someone who has paid $340 to learn it.